Master92 fd2f17f847 controller_fan: Replace else followed by single if with elif ...

Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>

2019-09-17 11:52:03 -04:00

..

display

uc1701: Add support for a reset line on SSD1306 displays

2019-08-17 22:14:02 -04:00

__init__.py

…

ad5206.py

…

adc_temperature.py

…

bed_mesh.py

…

bed_screws.py

…

bed_tilt.py

…

bltouch.py

bltouch: Improve handling of low pin_move_time configuration

2019-09-14 15:16:26 -04:00

board_pins.py

board_pins: Improve config error checking

2019-08-19 21:58:11 -04:00

bus.py

pins: Move reserved pin handling into PinResolver class

2019-08-19 12:57:59 -04:00

buttons.py

buttons: initialize mcu buttons based on inverted state

2019-07-05 20:01:07 -04:00

controller_fan.py

controller_fan: Replace else followed by single if with elif

2019-09-17 11:52:03 -04:00

delayed_gcode.py

delayed_gcode: initial implementation

2019-07-01 11:09:30 -04:00

delta_calibrate.py

…

dotstar.py

dotstar: Allow any number of chips to be daisy chained

2019-08-06 22:49:05 -04:00

endstop_phase.py

endstop_phase: Add tmc2209 and tmc5160 to list of tmc drivers

2019-06-23 11:27:18 -04:00

fan.py

…

filament_switch_sensor.py

filament_switch_sensor: Add a delay between dispatch of pause and execution of pause gcode

2019-09-08 20:42:43 -04:00

firmware_retraction.py

firmware_retract: Remove z_hop support

2019-07-10 19:25:56 -04:00

force_move.py

…

gcode_arcs.py

gcode_arcs: Add support for G2/G3 commands

2019-09-13 11:57:54 -04:00

gcode_button.py

gcode_button: Execute gcode when a button is pressed or released (#1745)

2019-06-21 18:06:31 -04:00

gcode_macro.py

gcode_macro: add iterator to status wrapper

2019-07-01 10:59:13 -04:00

heater_bed.py

…

heater_fan.py

…

heater_generic.py

…

homing_override.py

…

idle_timeout.py

…

manual_probe.py

…

manual_stepper.py

…

mcp4018.py

…

mcp4451.py

…

mcp4728.py

mcp4728: Update to better match printrbot revf requirements

2019-07-26 11:02:56 -04:00

multi_pin.py

…

neopixel.py

neopixel: Add support for WS2811 RGB pixel color order

2019-08-09 20:58:49 -04:00

output_pin.py

…

pause_resume.py

pause_resume: add CLEAR_PAUSE gcode

2019-06-28 12:44:49 -04:00

pid_calibrate.py

…

probe.py

probe: Rework the PROBE_ACCURACY command parameters

2019-07-10 15:21:09 -04:00

quad_gantry_level.py

…

query_endstops.py

mcu: Integrate query_endstop_wait() into query_endstop()

2019-07-10 10:43:20 -04:00

replicape.py

pins: Move reserved pin handling into PinResolver class

2019-08-19 12:57:59 -04:00

respond.py

…

safe_z_home.py

extra: Add Safe Z home extra

2019-08-09 20:49:17 -04:00

samd_sercom.py

…

screws_tilt_adjust.py

…

servo.py

…

skew_correction.py

skew_correction: add SKEW_PROFILE gcode

2019-06-29 10:58:46 -04:00

spi_temperature.py

serialhdl: Rename register_callback() to register_response()

2019-06-21 18:14:00 -04:00

static_digital_output.py

…

statistics.py

…

sx1509.py

sx1509: Minor cleanup - don't default print_time to 0

2019-06-25 18:19:05 -04:00

temperature_fan.py

temperature_fan: Allow min_speed to be set to zero

2019-09-14 15:35:09 -04:00

temperature_sensor.py

…

thermistor.py

…

tmc2130.py

tmc: Configure "intpol" field from TMCMicrostepHelper

2019-06-28 16:59:26 -04:00

tmc2208.py

tmc: Configure "intpol" field from TMCMicrostepHelper

2019-06-28 16:59:26 -04:00

tmc2209.py

tmc2209: Add support for sensorless homing

2019-08-19 12:05:09 -04:00

tmc2660.py

tmc: Configure "intpol" field from TMCMicrostepHelper

2019-06-28 16:59:26 -04:00

tmc5160.py

tmc: Configure "intpol" field from TMCMicrostepHelper

2019-06-28 16:59:26 -04:00

tmc_uart.py

tmc_uart: Make sure address is at least 0

2019-07-31 13:13:27 -04:00

tmc.py

tmc2209: Add support for sensorless homing

2019-08-19 12:05:09 -04:00

tsl1401cl_filament_width_sensor.py

…

verify_heater.py

…

virtual_sdcard.py

…

z_tilt.py

…