Kevin O'Connor 95eb00740b stm32: Avoid read+write modify instructions in can.c ...

Prefer explicitly setting the hardware registers and avoid using C
read and modify instructions where possible.  This avoids race
conditions where an interrupt or hardware change could cause subtle
corruption of the register state.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2021-02-02 15:17:14 -05:00

..

atsam

atsam: Support reading chip based temperature sensor on sam4e

2020-10-29 11:55:06 -04:00

atsamd

atsamd: Fix bug in sercom_pads mapping on samd21 in sercom.c

2021-02-01 10:55:38 -05:00

avr

Kconfig: Add a new CONFIG_HAVE_STRICT_TIMING build definition

2020-05-31 14:57:06 -04:00

generic

command: Fix handling of buffer passing in args[] on 64bit mcu

2020-10-30 14:04:12 -04:00

linux

ds18b20: new module for 1-wire temperature sensor (#3462)

2021-02-02 14:34:56 -05:00

lpc176x

lpc176x: Fix spi mode bits

2020-07-10 16:08:18 -04:00

pru

pru: Disable gpio mux configuration code

2020-12-04 16:10:13 -05:00

simulator

command: Fix handling of buffer passing in args[] on 64bit mcu

2020-10-30 14:04:12 -04:00

stm32

stm32: Avoid read+write modify instructions in can.c

2021-02-02 15:17:14 -05:00

adccmds.c

adccmds: Run gpio_adc_setup() before oid_alloc()

2019-01-13 11:03:30 -05:00

basecmd.c

stepper: Use a reusable interface to the "move queue"

2020-12-04 16:10:13 -05:00

basecmd.h

stepper: Use a reusable interface to the "move queue"

2020-12-04 16:10:13 -05:00

buttons.c

buttons: initialize mcu buttons based on inverted state

2019-07-05 20:01:07 -04:00

byteorder.h

byteorder: Add a header file defining common byteswap functions

2018-05-21 09:44:40 -04:00

command.c

command: Fix handling of buffer passing in args[] on 64bit mcu

2020-10-30 14:04:12 -04:00

command.h

command: Add command_decode_ptr() helper

2020-10-30 14:04:08 -04:00

compiler.h

…

ctr.h

ctr: Encode negative integers in normal hex notation

2019-08-22 13:06:44 -04:00

debugcmds.c

command: Add command_decode_ptr() helper

2020-10-30 14:04:08 -04:00

endstop.c

endstop: Rename mcu end_stop commands to endstop

2019-07-12 08:10:53 -04:00

gpiocmds.c

gpiocmds: Merge digital output and soft pwm code

2020-12-10 12:06:26 -05:00

i2ccmds.c

command: Add command_decode_ptr() helper

2020-10-30 14:04:08 -04:00

initial_pins.c

initial_pins: Add ability to configure output pins at mcu startup

2019-03-17 20:56:25 -04:00

initial_pins.h

initial_pins: Add ability to configure output pins at mcu startup

2019-03-17 20:56:25 -04:00

Kconfig

Kconfig: Only show the "usb ids" menu if low-level options are enabled

2020-05-31 21:05:04 -04:00

lcd_hd44780.c

command: Add command_decode_ptr() helper

2020-10-30 14:04:08 -04:00

lcd_st7920.c

command: Add command_decode_ptr() helper

2020-10-30 14:04:08 -04:00

Makefile

adxl345: Add support for adxl345 accelerometer

2020-09-05 09:11:04 -04:00

neopixel.c

neopixel: Fix neopixel_result message so that it contains an oid

2020-11-05 11:40:34 -05:00

pwmcmds.c

pwmcmds: Use move queue for hard PWM

2020-12-04 16:10:13 -05:00

sched.c

sched: Force sched_try_shutdown to be inlined

2018-10-13 11:47:00 -04:00

sched.h

pru: Support config_reset command to manually reset mcu

2017-09-03 23:16:38 -04:00

sensor_adxl345.c

sensor_adxl345: Remove unused stop_time parameter

2020-09-05 09:18:59 -04:00

spi_software.c

spi_software: Remove unused include file

2019-08-17 13:49:03 -04:00

spi_software.h

spi_software: Implementation of software spi

2019-02-13 11:52:20 -05:00

spicmds.c

command: Add command_decode_ptr() helper

2020-10-30 14:04:08 -04:00

spicmds.h

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

stepper.c

stepper: Use a reusable interface to the "move queue"

2020-12-04 16:10:13 -05:00

stepper.h

stepper: Introduce stepper_get_position command and remove from endstop.c

2017-03-09 14:54:52 -05:00

thermocouple.c

thermocouple: Define thermocouple types using enumerations

2019-03-17 19:38:18 -04:00

tmcuart.c

command: Add command_decode_ptr() helper

2020-10-30 14:04:08 -04:00