Innotex/Klipper
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
Files
1d7f6e1c13cdeb300bc18ab05c4ba843e2165821
Klipper/src
History
Kevin O'Connor 60ae92d143 stm32: Disable usb irqs in usbotg handlers 
It appears the usbotg controller can get confused if the usb irq
handler runs while processing a usb request.  Disable usb irqs during
usb processing to avoid this.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-09-12 08:12:51 -04:00
..
atsam
atsam: Enable flash loop caching optimization on sam4s
2019-09-08 09:11:41 -04:00
atsamd
armcm_link: Rename armcm_boot.lds.S to armcm_link.lds.S
2019-08-22 13:18:24 -04:00
avr
avr: Simplify spi mode setting
2019-05-07 23:02:20 -04:00
generic
armcm_link: Rename armcm_boot.lds.S to armcm_link.lds.S
2019-08-22 13:18:24 -04:00
linux
spicmds: Rework spi config commands
2019-08-06 18:56:53 -04:00
lpc176x
armcm_link: Rename armcm_boot.lds.S to armcm_link.lds.S
2019-08-22 13:18:24 -04:00
pru
pru: The TMR_CNT is cleared by writing all ones
2019-03-31 13:48:50 -04:00
simulator
simulator: Wrap code to 80 columns
2019-02-27 14:20:15 -05:00
stm32
stm32: Disable usb irqs in usbotg handlers
2019-09-12 08:12:51 -04:00
stm32f0
stm32f0: Remove trailing tab from Makefile
2019-07-21 21:49:22 -04:00
adccmds.c
adccmds: Run gpio_adc_setup() before oid_alloc()
2019-01-13 11:03:30 -05:00
basecmd.c
spicmds: Rework spi config commands
2019-08-06 18:56:53 -04:00
basecmd.h
spicmds: Rework spi config commands
2019-08-06 18:56:53 -04:00
buttons.c
buttons: initialize mcu buttons based on inverted state
2019-07-05 20:01:07 -04:00
byteorder.h
byteorder: Add a header file defining common byteswap functions
2018-05-21 09:44:40 -04:00
command.c
command: Wait to send ack until after processing commands
2018-05-28 10:43:40 -04:00
command.h
buildcommands: Match DECL_X names to the actual C macro names
2019-08-22 13:26:30 -04:00
compiler.h
compiler.h: Check if __aligned and __section macros are already defined
2016-06-13 23:18:59 -04:00
ctr.h
ctr: Encode negative integers in normal hex notation
2019-08-22 13:06:44 -04:00
debugcmds.c
debugcmds: Add support for reading/writing 32bit values
2019-02-07 11:50:14 -05:00
endstop.c
endstop: Rename mcu end_stop commands to endstop
2019-07-12 08:10:53 -04:00
gpiocmds.c
gpiocmds: Specify soft pwm duration in clock ticks
2019-05-26 11:09:32 -04:00
i2ccmds.c
bus: Change bus parameter in config_spi/config_i2c
2019-04-04 18:29:31 -04:00
initial_pins.c
initial_pins: Add ability to configure output pins at mcu startup
2019-03-17 20:56:25 -04:00
initial_pins.h
initial_pins: Add ability to configure output pins at mcu startup
2019-03-17 20:56:25 -04:00
Kconfig
stm32: Rename stm32f4/ directory to stm32/
2019-08-05 11:25:40 -04:00
lcd_hd44780.c
lcd_hd44780: Add micro-controller code for the HD44780 LCD chip
2018-03-06 11:30:34 -05:00
lcd_st7920.c
lcd_st7920: Add brief delay around gpio toggle calls on fast MCUs
2019-08-10 11:45:15 -04:00
Makefile
initial_pins: Only build when CONFIG_HAVE_GPIO is enabled
2019-07-24 01:09:45 -04:00
neopixel.c
neopixel: Rework timing so that it works on AVR micro-controllers
2019-08-07 15:37:05 -04:00
pwmcmds.c
pwmcmds: allow 16-bit resolution
2019-04-05 19:02:48 -04:00
sched.c
sched: Force sched_try_shutdown to be inlined
2018-10-13 11:47:00 -04:00
sched.h
pru: Support config_reset command to manually reset mcu
2017-09-03 23:16:38 -04:00
spi_software.c
spi_software: Remove unused include file
2019-08-17 13:49:03 -04:00
spi_software.h
spi_software: Implementation of software spi
2019-02-13 11:52:20 -05:00
spicmds.c
spicmds: Rework spi config commands
2019-08-06 18:56:53 -04:00
spicmds.h
spicmds: Rework spi config commands
2019-08-06 18:56:53 -04:00
stepper.c
stepper: Don't update SF_LAST_DIR if SF_NEED_RESET
2019-07-12 07:54:24 -04:00
stepper.h
stepper: Introduce stepper_get_position command and remove from endstop.c
2017-03-09 14:54:52 -05:00
thermocouple.c
thermocouple: Define thermocouple types using enumerations
2019-03-17 19:38:18 -04:00
tmcuart.c
tmcuart: Fix typo in function name
2019-09-01 14:56:09 -04:00