Move up the freeing of the stepper_move struct and setting of
s->position in stepper_load_next(). This simplifies the code and
will make it easier to add more logic to this function.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Increase the internal nominal clock from 8Mhz to 12Mhz - this improves
support for higher chip frequencies.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The rp2040 operates at a fast internal clock with a relatively slow
external timer and dividing down could result in a too small delay.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
There is no reason to use a higher internal PLL frequency. This
change also makes it possible to enable higher clock frequencies on
the stm32h723.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the helper functions to enable the peripheral clock instead of
directly manipulating the clock enable bits.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add optimized gpio functions for stm32h7 - caching the ODR register
can notably improve the performance of the gpio_out_toggle() code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
gpio reset calls are heavy.
gpio state are persistent between calls.
Drop useless calls.
Avoid calls if SDA does not changed.
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
On fast MCU software spi may violate maximally supported by TMC driver rate.
Add dynamic limits to overcome that.
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
Support setting individual options instead of one global option (
WANT_BUTTONS, WANT_TMCUART, WANT_NEOPIXEL, WANT_PULSE_COUNTER,
WANT_HX71X).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This option seems to be confusing ld's region usage checks (builds
that could fit in small chips are being reported as not fitting). The
option was disabled back in commit 4e8674d5 because it showed worse
results. However, recent versions of gcc seem to produce the same
results even if this option is enabled, so change the build to avoid
disabling that option on newer versions of gcc (those that have the
-ffat-lto-objects option - which is needed to ensure
compile_time_requests sections can be extracted with objcopy).
The PRU build is dependent on -fuse-linker-plugin, so enable that
option explicitly in its build.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The i2c_delay() function did not properly handle counter rollovers.
It also performed an expensive run-time divide.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It seems both ERRIE and LECIE must be enabled to get hardware error
interrupts. Without this, the rx_error and tx_error reports are
likely to always be zero.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a new "low level option" to allow users to configure if they want
to optimize for Trinamic drivers or traditional stepper motor drivers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for "step on both edges" to the main stepper_event_full()
code. This makes that mode of operation available even when the
micro-controller is not compiled for "optimized step on both edges".
It also enables the custom pulse duration support (step_pulse_ticks)
when in "step on both edges" mode.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
STM32F401 has USART6 on PA12/PA11 and PC7/PC6 with alternate
function mapping AF08. This can be used, for example, to connect
to the Elegoo Neptune 3, where PA12/PA11 are wired to an RJ10 plug
going to the stock screen.
Signed-off-by: Marius Petcu <marius@petcu.me>
